8/2/2023 0 Comments Arduino for mac m1![]() SMB Server mkdir /tmp/mnt & mount_smbfs /tmp/mnt & hdiutil mount /tmp/mnt/mds/MDSDiskImage.dmg & /Volumes/MacDeployStickResources/run Web Server hdiutil mount & /Volumes/MacDeployStickResources/run Depending on where the resources are located, the command will be different. It should be adjusted to match the name of the external volume (replace “mds” with the name of the volume that contains the MDS resources). Command: Listed is the command that will run in Terminal in the recovery partition.MDS will prompt to update the Automaton if it has older firmware than what is provided in the current MDS version. Version: View the current Automaton firmware version.These values can be adjusted using the Configure Mac Automaton sheet. It will then wait for a defined startup delay before issuing the commands for opening Terminal and running the specified command. ![]() The Automaton will press ⌘R a few seconds after it has been plugged in. SettingsĬlick “Configure Mac Automaton” to change options. Note: the MDS Automaton must be connected when the configuration sheet is shown as it only listens for a connection over a few seconds on initial power. Once the Configure sheet is displayed, plug in the Automaton using the provided USB cable. Guilherme Rambo writes about his coding and reverse engineering adventures.To configure the MDS Automaton, launch MDS and click the “Configure Mac Automaton” button. If you happen to know of a better solution, feel free to reach out on Twitter. I don’t feel particularly good about this, it seems that I should instead be replacing whatever is setting to point to my own version of Python instead, but I don’t have enough knowledge about how the environment works in the Arduino IDE, and being able to flash my projects to the board was more important than learning that. Restart the Arduino IDE and everything should work fine now. To do that, open ~/Library/Arduino15/packages/esp8266/hardware/esp8266/2.7.4/platform.txt in a text editor, then replace all occurrences of with the path to your own Python install, in the case of HomeBrew on M1, it would be /opt/homebrew/bin. But since I have installed Python 3 using HomeBrew, I can tweak the package to use that version instead. Upload error: Error: 2 UNKNOWN: uploading error: uploading error: exit status 1įor some reason, the upload tool included with the ESP8266 package seems to include its own version of Python, which for some other reason doesn’t really work in my particular environment. Make sure you have added the ESP8266 URL to “additional boards manager URLs” in the Arduino IDE settings (this works for both the Arduino Pro IDE as well as the regular one): Īfter installing the ESP8266 boards, if you try to upload your sketch to a board, you’re likely going to run into an error: pyserial or esptool directories not found next to this upload.py tool. Use pip3 from the new python3 that’s just been installed to install the pyserial library: pip3 install pyserial Then, use HomeBrew to install Python 3, which is required by the scripts in the ESP support for the Arduino IDE: brew install python3 HomeBrew has recently been updated with support for M1 Macs. The first step is to install HomeBrew, if you don’t have it yet. ![]() I’m just laying out the steps that worked for me, but I am by no means an expert on the subject, so if this doesn’t work for you, it’s very unlikely that I’ll be able to help you out any further. Obligatory disclaimer: this is not a tutorial. It wasn’t hard to figure out a workaround, so I decided to write it here both as a future reference for myself as well as a helpful resource for others. That’s where I hit a problem, because I’ve been using the new M1 MacBook Air as my work computer for a while, but unfortunately the ESP support for the Arduino IDE doesn’t work out of the box. To make things easier for me, I decided to program my boards with the Arduino Pro IDE, which I’m already familiar with, so I had to install the libraries for the ESP8266. I started out with an Arduino board to test things out, but then people reminded me of the ESP32 and ESP8266 microcontrollers, which integrate BLE and WiFi and can run the HomeKit Accessory Protocol (HAP) natively. ![]() Recently, I decided it would be a fun side project to turn a cheap air humidifier into a HomeKit accessory. Programming microcontrollers is something I’ve always liked to do, there’s something very satisfying about writing code that controls things in “real life”, instead of just pixels on a screen.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |